300 lines
12 KiB
C
300 lines
12 KiB
C
/* Megumin LED display firmware
|
|
* Copyright (C) 2018 Sebastian Götte <code@jaseg.net>
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "adc.h"
|
|
|
|
#include <stdbool.h>
|
|
#include <stdlib.h>
|
|
|
|
#define DETECTOR_CHANNEL a
|
|
|
|
volatile uint16_t adc_buf[ADC_BUFSIZE];
|
|
volatile struct adc_state adc_state = {0};
|
|
#define st adc_state
|
|
volatile struct adc_measurements adc_data;
|
|
|
|
static void adc_dma_init(int burstlen, bool enable_interrupt);
|
|
static void adc_timer_init(int psc, int ivl);
|
|
|
|
|
|
/* Mode that can be used for debugging */
|
|
void adc_configure_scope_mode(uint8_t channel_mask, int sampling_interval_ns) {
|
|
/* The constant SAMPLE_FAST (0) when passed in as sampling_interval_ns is handled specially in that we turn the ADC
|
|
to continuous mode to get the highest possible sampling rate. */
|
|
|
|
/* First, disable trigger timer, DMA and ADC in case we're reconfiguring on the fly. */
|
|
TIM1->CR1 &= ~TIM_CR1_CEN;
|
|
ADC1->CR &= ~ADC_CR_ADSTART;
|
|
DMA1_Channel1->CCR &= ~DMA_CCR_EN;
|
|
|
|
/* keep track of current mode in global variable */
|
|
st.adc_mode = ADC_SCOPE;
|
|
|
|
adc_dma_init(sizeof(adc_buf)/sizeof(adc_buf[0]), true);
|
|
|
|
/* Clock from PCLK/4 instead of the internal exclusive high-speed RC oscillator. */
|
|
ADC1->CFGR2 = (2<<ADC_CFGR2_CKMODE_Pos); /* Use PCLK/4=12MHz */
|
|
/* Sampling time 13.5 ADC clock cycles -> total conversion time 2.17us*/
|
|
ADC1->SMPR = (2<<ADC_SMPR_SMP_Pos);
|
|
|
|
/* Setup DMA and triggering */
|
|
if (sampling_interval_ns == SAMPLE_FAST) /* Continuous trigger */
|
|
ADC1->CFGR1 = ADC_CFGR1_DMAEN | ADC_CFGR1_DMACFG | ADC_CFGR1_CONT;
|
|
else /* Trigger from timer 1 Channel 4 */
|
|
ADC1->CFGR1 = ADC_CFGR1_DMAEN | ADC_CFGR1_DMACFG | (2<<ADC_CFGR1_EXTEN_Pos) | (1<<ADC_CFGR1_EXTSEL_Pos);
|
|
ADC1->CHSELR = channel_mask;
|
|
/* Perform self-calibration */
|
|
ADC1->CR |= ADC_CR_ADCAL;
|
|
while (ADC1->CR & ADC_CR_ADCAL)
|
|
;
|
|
/* Enable conversion */
|
|
ADC1->CR |= ADC_CR_ADEN;
|
|
ADC1->CR |= ADC_CR_ADSTART;
|
|
|
|
if (sampling_interval_ns == SAMPLE_FAST)
|
|
return; /* We don't need the timer to trigger in continuous mode. */
|
|
|
|
/* An ADC conversion takes 1.1667us, so to be sure we don't get data overruns we limit sampling to every 1.5us.
|
|
Since we don't have a spare PLL to generate the ADC sample clock and re-configuring the system clock just for this
|
|
would be overkill we round to 250ns increments. The minimum sampling rate is about 60Hz due to timer resolution. */
|
|
int cycles = sampling_interval_ns > 1500 ? sampling_interval_ns/250 : 6;
|
|
if (cycles > 0xffff)
|
|
cycles = 0xffff;
|
|
adc_timer_init(12/*250ns/tick*/, cycles);
|
|
}
|
|
|
|
/* Regular operation receiver mode */
|
|
void adc_configure_monitor_mode(const struct command_if_def *cmd_if, int ivl_us) {
|
|
/* First, disable trigger timer, DMA and ADC in case we're reconfiguring on the fly. */
|
|
TIM1->CR1 &= ~TIM_CR1_CEN;
|
|
ADC1->CR &= ~ADC_CR_ADSTART;
|
|
DMA1_Channel1->CCR &= ~DMA_CCR_EN;
|
|
|
|
/* keep track of current mode in global variable */
|
|
st.adc_mode = ADC_MONITOR;
|
|
|
|
for (int i=0; i<NCH; i++)
|
|
st.adc_aggregate[i] = 0;
|
|
st.mean_aggregator[0] = st.mean_aggregator[1] = st.mean_aggregator[2] = 0;
|
|
st.mean_aggregate_ctr = 0;
|
|
|
|
st.det_st.hysteresis_mv = 6000;
|
|
st.det_st.base_interval_cycles = 10;
|
|
|
|
st.det_st.sync = 0;
|
|
st.det_st.last_bit = 0;
|
|
st.det_st.committed_len_ctr = st.det_st.len_ctr = 0;
|
|
xfr_8b10b_reset((struct state_8b10b_dec *)&st.det_st.rx8b10b);
|
|
reset_receiver((struct proto_rx_st *)&st.det_st.rx_st, cmd_if);
|
|
|
|
adc_dma_init(NCH, true);
|
|
|
|
/* Setup DMA and triggering: Trigger from Timer 1 Channel 4 */
|
|
ADC1->CFGR1 = ADC_CFGR1_DMAEN | ADC_CFGR1_DMACFG | (2<<ADC_CFGR1_EXTEN_Pos) | (1<<ADC_CFGR1_EXTSEL_Pos);
|
|
/* Clock from PCLK/4 instead of the internal exclusive high-speed RC oscillator. */
|
|
ADC1->CFGR2 = (2<<ADC_CFGR2_CKMODE_Pos); /* Use PCLK/4=12MHz */
|
|
/* Sampling time 13.5 ADC clock cycles -> total conversion time 2.17us*/
|
|
ADC1->SMPR = (2<<ADC_SMPR_SMP_Pos);
|
|
/* Internal VCC and temperature sensor channels */
|
|
ADC1->CHSELR = ADC_CHSELR_CHSEL0 | ADC_CHSELR_CHSEL1 | ADC_CHSELR_CHSEL16 | ADC_CHSELR_CHSEL17;
|
|
/* Enable internal voltage reference and temperature sensor */
|
|
ADC->CCR = ADC_CCR_TSEN | ADC_CCR_VREFEN;
|
|
/* Perform ADC calibration */
|
|
ADC1->CR |= ADC_CR_ADCAL;
|
|
while (ADC1->CR & ADC_CR_ADCAL)
|
|
;
|
|
/* Enable ADC */
|
|
ADC1->CR |= ADC_CR_ADEN;
|
|
ADC1->CR |= ADC_CR_ADSTART;
|
|
|
|
adc_timer_init(SystemCoreClock/1000000/*1.0us/tick*/, ivl_us);
|
|
}
|
|
|
|
static void adc_dma_init(int burstlen, bool enable_interrupt) {
|
|
/* Configure DMA 1 Channel 1 to get rid of all the data */
|
|
DMA1_Channel1->CPAR = (unsigned int)&ADC1->DR;
|
|
DMA1_Channel1->CMAR = (unsigned int)&adc_buf;
|
|
DMA1_Channel1->CNDTR = burstlen;
|
|
DMA1_Channel1->CCR = (0<<DMA_CCR_PL_Pos);
|
|
DMA1_Channel1->CCR |=
|
|
DMA_CCR_CIRC /* circular mode so we can leave it running indefinitely */
|
|
| (1<<DMA_CCR_MSIZE_Pos) /* 16 bit */
|
|
| (1<<DMA_CCR_PSIZE_Pos) /* 16 bit */
|
|
| DMA_CCR_MINC
|
|
| (enable_interrupt ? DMA_CCR_TCIE : 0); /* Enable transfer complete interrupt. */
|
|
|
|
if (enable_interrupt) {
|
|
/* triggered on transfer completion. We use this to process the ADC data */
|
|
NVIC_EnableIRQ(DMA1_Channel1_IRQn);
|
|
NVIC_SetPriority(DMA1_Channel1_IRQn, 2<<5);
|
|
} else {
|
|
NVIC_DisableIRQ(DMA1_Channel1_IRQn);
|
|
DMA1->IFCR |= DMA_IFCR_CGIF1;
|
|
}
|
|
|
|
DMA1_Channel1->CCR |= DMA_CCR_EN; /* Enable channel */
|
|
}
|
|
|
|
static void adc_timer_init(int psc, int ivl) {
|
|
TIM1->BDTR = TIM_BDTR_MOE; /* MOE is needed even though we only "output" a chip-internal signal TODO: Verify this. */
|
|
TIM1->CCMR2 = (6<<TIM_CCMR2_OC4M_Pos); /* PWM Mode 1 to get a clean trigger signal */
|
|
TIM1->CCER = TIM_CCER_CC4E; /* Enable capture/compare unit 4 connected to ADC */
|
|
TIM1->CCR4 = 1; /* Trigger at start of timer cycle */
|
|
/* Set prescaler and interval */
|
|
TIM1->PSC = psc-1;
|
|
TIM1->ARR = ivl-1;
|
|
/* Preload all values */
|
|
TIM1->EGR |= TIM_EGR_UG;
|
|
TIM1->CR1 = TIM_CR1_ARPE;
|
|
/* And... go! */
|
|
TIM1->CR1 |= TIM_CR1_CEN;
|
|
}
|
|
|
|
/* This acts as a no-op that provides a convenient point to set a breakpoint for the debug scope logic */
|
|
static void gdb_dump(void) {
|
|
}
|
|
|
|
/* Called on reception of a bit. This feeds the bit to the 8b10b state machine. When the 8b10b state machine recognizes
|
|
* a received symbol, this in turn calls receive_symbol. Since this is called at sampling time roughly halfway into a
|
|
* bit being received, receive_symbol is called roughly half-way through the last bit of the symbol, just before the
|
|
* symbol's end.
|
|
*/
|
|
void receive_bit(struct bit_detector_st *st, int bit) {
|
|
int symbol = xfr_8b10b_feed_bit((struct state_8b10b_dec *)&st->rx8b10b, bit);
|
|
if (symbol == -K28_1)
|
|
st->sync = 1;
|
|
|
|
if (symbol == -DECODING_IN_PROGRESS)
|
|
return;
|
|
|
|
if (symbol == -DECODING_ERROR)
|
|
st->sync = 0;
|
|
/* Fall through so we also pass the error to receive_symbol */
|
|
|
|
GPIOA->BSRR = 1<<9; /* debug */
|
|
receive_symbol(&st->rx_st, symbol);
|
|
GPIOA->BRR = 1<<9; /* debug */
|
|
|
|
/* Debug scope logic */
|
|
/*
|
|
static int debug_buf_pos = 0;
|
|
if (st->sync) {
|
|
if (debug_buf_pos < NCH) {
|
|
debug_buf_pos = NCH;
|
|
} else {
|
|
adc_buf[debug_buf_pos++] = symbol;
|
|
|
|
if (debug_buf_pos >= sizeof(adc_buf)/sizeof(adc_buf[0])) {
|
|
debug_buf_pos = 0;
|
|
st->sync = 0;
|
|
gdb_dump();
|
|
for (int i=0; i<sizeof(adc_buf)/sizeof(adc_buf[0]); i++)
|
|
adc_buf[i] = -255;
|
|
}
|
|
}
|
|
}
|
|
*/
|
|
}
|
|
|
|
/* From a series of detected line levels, extract discrete bits. This self-synchronizes to signal transitions. This
|
|
* expects base_interval_cycles to be set correctly. When a bit is detected, this calls receive_bit(st, bit). The call
|
|
* to receive_bit happens at the sampling point about half-way through the bit being received.
|
|
*/
|
|
void bit_detector(struct bit_detector_st *st, int a) {
|
|
int new_bit = st->last_bit;
|
|
int diff = a-5500; /* FIXME extract constants */
|
|
if (diff < - st->hysteresis_mv/2)
|
|
new_bit = 0;
|
|
else if (diff > st->hysteresis_mv/2)
|
|
new_bit = 1;
|
|
else
|
|
blank(); /* Safety, in case we get an unexpected transition */
|
|
|
|
st->len_ctr++;
|
|
if (new_bit != st->last_bit) { /* On transition */
|
|
st->last_bit = new_bit;
|
|
st->len_ctr = 0;
|
|
st->committed_len_ctr = st->base_interval_cycles>>1; /* Commit first half of bit */
|
|
|
|
} else if (st->len_ctr >= st->committed_len_ctr) {
|
|
/* The line stayed constant for a longer interval than the commited length. Interpret this as a transmitted bit.
|
|
*
|
|
* +-- Master clock edges -->| - - - - |<-- One bit period
|
|
* | | |
|
|
* 1 X X X X X X X X
|
|
* ____/^^^^*^^^^\_______________________________________/^^^^*^^^^^^^^^*^^^^\__________________________________
|
|
* 0 v ^ v ^
|
|
* | | | |
|
|
* | +-------------------------------+ +---------+
|
|
* | | |
|
|
* At this point, commit 1/2 bit (until here). This When we arrive at the committed value, commit next
|
|
* happens in the block above. full bit as we're now right in the middle of the
|
|
* first bit. This happens in the line below.
|
|
*/
|
|
|
|
/* Commit second half of this and first half of possible next bit */
|
|
st->committed_len_ctr += st->base_interval_cycles;
|
|
receive_bit(st, st->last_bit);
|
|
}
|
|
}
|
|
|
|
void DMA1_Channel1_IRQHandler(void) {
|
|
GPIOA->BSRR = 1<<5;
|
|
/* ISR timing measurement for debugging */
|
|
//int start = SysTick->VAL;
|
|
|
|
/* Clear the interrupt flag */
|
|
DMA1->IFCR |= DMA_IFCR_CGIF1;
|
|
|
|
if (st.adc_mode == ADC_SCOPE)
|
|
return;
|
|
|
|
/* FIXME This code section currently is a mess since I left it as soon as it worked. Re-work this and try to get
|
|
* back all the useful monitoring stuff, in particular temperature. */
|
|
|
|
/* This has been copied from the code examples to section 12.9 ADC>"Temperature sensor and internal reference
|
|
* voltage" in the reference manual with the extension that we actually measure the supply voltage instead of
|
|
* hardcoding it. This is not strictly necessary since we're running off a bored little LDO but it's free and
|
|
* the current supply voltage is a nice health value.
|
|
*/
|
|
// FIXME DEBUG adc_data.vcc_mv = (3300 * VREFINT_CAL)/(st.adc_aggregate[VREF_CH]);
|
|
|
|
int64_t vcc = 3300;
|
|
/* FIXME debug
|
|
int64_t vcc = adc_data.vcc_mv;
|
|
int64_t read = st.adc_aggregate[TEMP_CH] * 10 * 10000;
|
|
int64_t cal = TS_CAL1 * 10 * 10000;
|
|
adc_data.temp_celsius_tenths = 300 + ((read/4096 * vcc) - (cal/4096 * 3300))/43000;
|
|
*/
|
|
|
|
/* Calculate the line voltage from the measured ADC voltage and the used resistive divider ratio */
|
|
const long vmeas_r_total = VMEAS_R_HIGH + VMEAS_R_LOW;
|
|
//int a = adc_data.vmeas_a_mv = (st.adc_aggregate[VMEAS_A]*(vmeas_r_total * vcc / VMEAS_R_LOW)) >> 12;
|
|
int a = adc_data.vmeas_a_mv = (adc_buf[VMEAS_A]*13300) >> 12;
|
|
bit_detector((struct bit_detector_st *)&st.det_st, a);
|
|
|
|
/* ISR timing measurement for debugging */
|
|
/*
|
|
int end = SysTick->VAL;
|
|
int tdiff = start - end;
|
|
if (tdiff < 0)
|
|
tdiff += SysTick->LOAD;
|
|
st.dma_isr_duration = tdiff;
|
|
*/
|
|
GPIOA->BRR = 1<<5;
|
|
}
|
|
|